The parabolic trough solar collector has a very high absorber tube temperature due to the concentration of solar radiation. The high temperature leads to large heat loss to the environment which reduces efficiency of the parabolic trough collector. The heat loss reduction can be obtained by adopting a multi-pass fluid flow arrangement. In this chapter, airflow travels in three passes of the receiver to absorb heat from the glass covers and absorber tube to decrease surface temperatures. 1D mathematical model is developed to evaluate effective efficiency and the temperature distribution of surfaces and fluid. The mathematical modeling is based on air temperature gradients and solved by a numerical integration. Diameter ratios of outer glass to inner glass (r23) and inner glass to absorber tube (r12), Reynolds number (Re), and tube length (L) are varied to examine the efficiency and the temperature distribution. Results showed that the highest efficiency is archived at r23 = 1.55 and r12 in the range of 1.45 to 1.5. The efficiency increases with Re and decreases with L due to dominant heat transfer in terms of thermohydraulic behavior of a concentrating solar collector. With the optimum ratios, absorber tube temperature can reduce 15 K compared with another case.
- Concentric tube heat exchanger
- 1D modeling
- parabolic trough collector
- effective efficiency
- solar air heater
Today, energy saving is a matter of great concern due to the depletion of fossil fuels as well as environmental pollution. Faced with that situation, the problem is that we must take advantage of available energy sources and use them for a long time without emitting toxic substances that affect the current living environment. Solar energy is a very abundant, completely free, environmentally friendly and long-lasting source of energy. Besides, it is possible to reduce the amount of toxic waste into the environment and contribute to saving a significant amount of costs when perceiving how to apply solar energy in daily life. Producing hot air by solar energy is an efficient and green solution by using a solar air heater. Flat-plate solar collector is often used in the range of moderately hot air temperature [1, 2, 3]. To generate greater air temperature, concentrating solar collectors are used. There are several types of concentrating collector such as linear Fresnel collector, dish collector, and parabolic trough collector. The parabolic trough collector is attributed to the most widespread one . Sketch and pictorial view of a parabolic trough solar collector are shown in Figures 1 and 2. When the intensity of solar radiation reaches the parabolic surface, solar energy is reflected and concentrated into the focus of the parabola where locates a thermal receiver. Here the heating process takes place to heat up a heat transfer fluid inside the receiver.
Elakhdar et al.  used a parabolic trough collector to power the generator of an organic Rankine plant. The results shown that the heat transfer fluid temperature in the receiver tube is up to 430 K and the thermal efficiency of the plant is 0.14. Li and Yuan  employed a parabolic trough collector for lighting and heating purposes. The results were reported that the lighting efficiency reaches 16.3%, the thermal efficiency 23.1% and the payback period less than 10 years. Bozorg et al.  numerically investigated a parabolic trough collector with nanofluid as a heat transfer media. It is proved that heat transfer, pressure drop, and thermal efficiency increase linearly with Reynolds number. Bellos et al.  examined a parabolic trough collector for thermal energy storage. The thermal efficiency and exergy efficiency of their system indicated 68.7% and 8.5%, respectively. Higher storage tank volume is recommended to yield higher thermal efficiency. Okonkwo et al.  studied different configurations of absorber tube including smooth tube, finned tube, twisted tape inserted tube, and converging–diverging tube. The results exhibited that the converging–diverging absorber tube demonstrated the highest exergy efficiency. In addition, the optical losses are the main components of exergy losses. Kaloudis et al.  simulated the absorber tube with an inner solid plug as a flow restriction device. In the study, the heat transfer fluid of Al2O3 nanofluid 4% revealed the best collector efficiency. Ray et al.  conducted a numerical analysis of selective coatings on the absorber tube. The thermal efficiency can be increased up to 34.6% by the selective coating. Tzivanidis and Bellos  used a parabolic trough collector to drive an absorption chiller which is to cool a room. The size of collector and thermal storage tank were determined to meet cooling load of a given space. Ghasemi and Ranjbar  compared heat transfer fluids of water and nanofluid inside a absorber tube. They confirmed that the nanofluid can improve heat transfer rate compared with the water. Nain et al.  employed the U-tube in a parabolic trough air collector. The tube was covered by the evacuated glass tube to minimize heat loss. The maximum outlet air temperature of 150°C was observed.
From the above literature review, it can be seen that there are many measures to enhance the performance of the parabolic trough solar collector. The present study proposes a triple-pass parabolic trough solar collector configuration so that the heat transfer fluid receives heat from the glass cover and absorber tube surfaces. Thus, the surface temperatures can be reduced leading to increase the collector efficiency. The independent parameters consist of tube diameters, collector length and Reynolds number of the heat transfer fluid to deduce heat transfer characteristics.
2. One-dimensional modeling
Figure 3 shows the schematic diagram of the triple-pass receiver. The receiver consists of an outer glass tube, an inner glass tube and an absorber. The tubes are fitted concentrically to each other so that the airflow moves in the three spaces. Air travels from the outermost annular space followed by the inner annular space and the inside of the absorber tube. Figure 4 displays a diagram of thermal energy transfer between surfaces and the airflow and a thermal resistance circuit in which the heat conduction resistance of the tubes is neglected. The receiver collects solar radiation from the top half and concentrated radiation from the bottom half. The thermal balance for the glass tube 1 is written as Eq. (1). The solar thermal energy absorbed by the glass is equal to the heat transferred by radiation and convection to the environment, the heat transferred by convection to the fluid in the outer annulus (first pass), and the heat transferred by radiation to the glass tube 2 :
where I is solar radiation absorbed by the receiver and As is surface area of a tube. Solar radiation absorbed by the receiver is the sum of heat flux up and heat flux down :
The surface areas can be determined as:
Tsky is the sky temperature. .
where is aperture area of the parabolic trough.
The temperature variation of the air along the axial direction in the first pass is due to convective heat exchange with the glasses 1 and 2:
Similar to the glass tube 1, heat exchange of the glass tube 2 is written as:
The temperature variation of the air in the second pass is given by:
Heat balance of the absorber tube is presented as:
The temperature variation of the air in the third pass is owing to convection heat transfer with the absorber tube surface:
Convection heat transfer coefficient due to wind :
Forced convection heat transfer coefficient of the airflow in three passes by Dittus-Boelter correlation :
where Re1, Re2 and Re are respectively Reynolds number in passes 1, 2, and 3. Pr is Prandtl number.
In the above equations, De is the equivalent diameter of an annulus. The diameter can be estimated by:
Radiation heat transfer coefficient of the outer glass to the sky :
Radiation heat transfer coefficient of two glass tubes :
Radiation heat transfer coefficient of the inner glass tube and the absorber tube :
Air velocities in passes (V1, V2, and V3) can be evaluated by mass conservation as:
The energy amount of air received when passing through the receiver is determined as follows:
As the flow rate and receiver size change, the pumping power will also change to transport the fluid. The useful hydraulic energy of the air received from a blower is calculated as follows:
where ΔP is the pressure difference of the air across the receiver. Because of significant length of the receiver, minor losses are omitted. The pressure drop due to friction in three 3 passes can be computed as:
where f is the friction factor of the air with the tube surface. The factor is calculated from the Blasius equation as follows :
The effective efficiency of a parabolic trough collector taking into account the heat received, the power dissipated relative to the radiation absorbed by the receiver is calculated as follows:
where Co is thermal energy conversion factor, Co = 0.2 .
In this study, the absorber tube diameter was fixed. The diameter of the glass tubes, the Reynolds number of the air in the absorber tube, and the receiver length varied to investigate the axial temperature distribution and the collector efficiency. The diameters of the glasses change according to the diameter ratios which are defined as follows:
Table 1 presents the parameters entered into the mathematical model. The thermophysical parameters of the air (specific heat cp, thermal conductivity k, density ρ, and dynamic viscosity μ) are estimated at the ambient temperature. Temperature variations of three surfaces and air in three passes can be solved by numerical integrals of temperature gradient equations, i.e., Eqs. (7), (9), and (11). The one-dimensional (1D) computational domain along the tube is divided into control volumes corresponding to a spatial step Δx. Solving the ordinary differential equations can be utilized ode45 function in MATLAB software  or integral function in EES software . Figure 5 presents a comparison of the air flow temperature variation in a double-pass solar air heater between the results from the code developed in this study and those of the literature . It can be seen that the two results are close to each other and the difference is not significant. Therefore, the model formulation in this study is accuracy to perform the parametric study for the triple pass parabolic trough solar air collector.
|Concentration ratio||CR = 10|
|Solar radiation||Ip = 848 W/m2|
|Ambient temperature||Ta = 27°C|
|Absorptivity of glass covers||αg1 = αg2 = 0.05|
|Absorptivity of absorber tube||αp = 0.92|
|Emissivity of glass covers||εg1 = εg2 = 0.92|
|Emissivity of absorber tube||εp = 0.92|
|Transmissivity of glass cover||τg1 = τg2 = 0.84|
|Wind velocity||Vw = 1 m/s|
|Absorber tube diameter||d1 = 42 mm|
3. Results and discussion
This section investigates the influence of Reynolds number in the range 10000 to 16000, tube diameter ratios (r23 and r12) from 1.2 to 2, and tube length from 1.5 to 3.5 m on the collector efficiency and temperature distribution of the receiver. Figure 6 shows the effect of Re and r23 on the performance. It can be seen that when the Re number increases, the performance increases. For flat-plate air collectors, efficiency can peak at some Re. However, for a concentrating collector, the thermal duty is very large compared to pumping power. Therefore, when Re increases, the heat transfer rate increases more than increase in the pressure loss penalty. However, the efficiency increases slightly with the Re number because the pumping power increases significantly with the flow rate. At fixed Re, the performance peaks at certain r23. As the ratio increases, the diameter of the glass covers increases, which reduces the heat transfer rate due to the decrease in air velocity. Conversely, increasing this ratio reduces the pressure loss in the two annuli. This trade-off leads to the optimal r23. Figure 6 shows that the optimal r23 value is almost unchanged with Re, i.e., r23, opt = 1.55. Figure 7 presents the effect of the ratio of inner glass tube diameter to absorber tube diameter on the efficiency. The effect of r12 can be seen to be more pronounced than that of r23. This is attributed to mainly heat exchange in the second pass due to the high temperatures of the absorber tube and glass 2. The optimum r12 varies over a wider range from 1.45 to 1.5. Also, at certain Re number, the performance changes drastically with r12, especially at large Re numbers. At Re = 16000, the efficiency varies from 0.59 to 0.6 with r23, from 0.575 to 0.605 with r12.
Figure 8 depicts the effect of collector length (L) on collector efficiency. It is observed that as the length increases, the efficiency decreases. It is noted that for a concentrating collector, the thermal power is very large compared to the pumping power. Therefore, the optimum L and Re are not found to maximize the efficiency as can be observed in flat-plate solar collectors. As the length increases, at a certain pass, the air temperature increases, reducing the temperature difference between the heat exchanger surfaces and the air temperature. This small temperature difference causes poor heat transfer rate. The reduction in efficiency with the length in the concentrator is also similar to that of the flat plate collector .
Figures 9 and 10 illustrate the distributions of the six temperatures along the tube length at Re = 10000. Figure 9 plots the temperatures at the optimal diameter ratios for this Re, i.e., r12 = 1.44 and r23 = 1.56. While Figure 10 represents worst-case temperatures (r12 = 2 and r23 = 1.2) for the sake of comparison. It is clear that the average temperature of the absorber tube decreases markedly from 160°C (the worst case) to 145°C (the optimum case). This reveals the optimal case owning better heat exchange of the fluid in passes 2 and 3 with absorber tube surface and smaller heat loss. For the optimal case, the absorber tube temperature increases with the air temperature in the second pass. In contrast, the absorber tube temperature increases with the air temperature in third pass for the worst case. Furthermore, the temperature cross between the air in pass 1 and glass 1 occurs in the very short segment from the inlet in the worst case. The temperature differences in pass 2 of Figures 9 and 10 are 55 K and 28 K, respectively. From Figures 9 and 10 it can be recognized that there are two temperature crosses between Tf1 and Tg1, and between Tf2 and Tg2. If shorter tubes are used, a temperature cross may not occur. Therefore, it can be concluded that collector efficiency decreases with increasing tube length by means of the current axial temperature analysis.
A 1D analytical model has been presented in this chapter to predict the local temperature of fluid and heat exchanger surfaces of the triple-pass parabolic trough solar collector. Some important conclusions are drawn as follows:
The diameter ratios of outer to inner glasses of 1.55 and the inner glass to absorber tube in the range of 1.45 to 1.5 achieve the greatest effective efficiency.
The efficiency increases with Reynolds number and decreases with tube length. In other words, optimum Reynolds number and tube length were not found due to the fact that thermal power prevails over pumping power for a concentrating solar collector.
The absorber tube temperature is reduced up to 15 K with optimal diameter ratios.
The effect of r12 on efficiency is more significant than that of r23 due to the strong heat exchange of the airflow in the annular space between the absorber tube and the inner glass tube.
This research is funded by the Vietnam National University-Ho Chi Minh City (VNU-HCM) under grant number B2021-20-06.
Conflict of interest
The authors declare no conflict of interest.
Phu NM, Luan NT. A Review of Energy and Exergy Analyses of a Roughened Solar Air Heater. Journal of Advanced Research in Fluid Mechanics and Thermal Sciences. 2020;77(2):160-175
Phu NM, Hap NV. Performance Evaluation of a Solar Air Heater Roughened with Conic-Curve Profile Ribs Based on Efficiencies and Entropy Generation. Arabian Journal for Science and Engineering. 2020;45(11):9023–9035
Phu NM, Hung HN, Tu NT, Van Hap N. Analytical predictions of exergoeconomic performance of a solar air heater with surface roughness of metal waste. Journal of Thermal Analysis & Calorimetry. 2021;144(5)
Elakhdar M, Landoulsi H, Tashtoush B, Nehdi E, Kairouani L. A combined thermal system of ejector refrigeration and Organic Rankine cycles for power generation using a solar parabolic trough. Energy Conversion and Management. 2019;199:111947
Li T, Yuan C. An optimal design analysis of a novel parabolic trough lighting and thermal system. International Journal Of Energy Research. 2016;40(9):1193-1206
Bozorg MV, Doranehgard MH, Hong K, Xiong Q. CFD study of heat transfer and fluid flow in a parabolic trough solar receiver with internal annular porous structure and synthetic oil–Al2O3 nanofluid. Renewable Energy. 2020;145:2598-2614
Bellos E, Tzivanidis C, Belessiotis V. Daily performance of parabolic trough solar collectors. Solar Energy. 2017;158:663-678
Okonkwo EC, Abid M, Ratlamwala TA. Effects of synthetic oil nanofluids and absorber geometries on the exergetic performance of the parabolic trough collector. International Journal of Energy Research. 2018;42(11):3559-3574
Kaloudis E, Papanicolaou E, Belessiotis V. Numerical simulations of a parabolic trough solar collector with nanofluid using a two-phase model. Renewable Energy. 2016;97:218-229
Ray S, Tripathy AK, Sahoo SS, Bindra H. Performance analysis of receiver of parabolic trough solar collector: E ffect of selective coating, vacuum and semitransparent glass cover. International Journal of Energy Research. 2018;42(13):4235-4249
Tzivanidis C, Bellos E. The use of parabolic trough collectors for solar cooling–A case study for Athens climate. Case Studies in Thermal Engineering. 2016;8:403-413
Ghasemi SE, Ranjbar A. Effect of nanoparticles in working fluid on thermal performance of solar parabolic trough collector. Journal of Molecular Liquids. 2016;222:156-166
Nain S, Parinam A, Kajal S. Experimental study and analysis of air heating system using a parabolic trough solar collector. International Journal of Ambient Energy. 2018;39(2):143-146
Thao PB, Truyen DC, Phu NM. CFD Analysis and Taguchi-Based Optimization of the Thermohydraulic Performance of a Solar Air Heater Duct Baffled on a Back Plate. Applied Sciences. 2021;11(10):4645
Nguyen Thanh L, Nguyen Minh P. First and Second Law Evaluation of Multipass Flat-Plate Solar Air Collector and Optimization Using Preference Selection Index Method. Mathematical Problems in Engineering. 2021;2021:5563882
Matheswaran M, Arjunan T, Somasundaram D. Energetic, exergetic and enviro-economic analysis of parallel pass jet plate solar air heater with artificial roughness. Journal of Thermal Analysis and Calorimetry. 2019;136(1):5-19
Phu NM, Lee GS. Characteristics of pressure and force considering friction in a closed cylinder with a holed piston. Journal of Mechanical Science and Technology. 2014;28(6):2409-2415
Phu NM. A compact EES program to predict the axial temperature distribution in triple-fluid heat exchanger. Science & Technology Development Journal. 2020;3(3):452-460
Ramani B, Gupta A, Kumar R. Performance of a double pass solar air collector. Solar energy. 2010;84(11):1929-1937